Next day delivery. Pre order. Retail Price 3. EVID 2. Add to cart. Rigging elements with angles for A10i onto or under KS21i. Rigging plates for A10i Wide. Fastening bracket for A15i, A10i and KS21i. Flying frame for vertical deployment of A10i. Fastening bracket with angles for A10i. Rigging plates for flying two A10i with A-U10i. Rear rigging plates for A15i and A10i onto or under KS21i. End rear rigging plates for A15i and A10i onto or under KS21i.
U-bracket for A15i. U-bracket for A10i. End rigging plates for A10i Wide. Login Contact Menu. Login Menu. Badge request. Industry : Audio. Dock Pullman — Stand s , L-ISA Processor. Kara II. Kiva II. A15i Focus. A15i Wide.
A15 Focus. A15 Wide. A10i Focus. A10i Wide. A10 Focus. A10 Wide. Syva Sub. Syva Low. X15 HiQ. Identifiant ou adresse e-mail. Mot de passe.
|A10i wide||Amd a10 pro 7350b|
|The nightmare before christmas oogie s revenge||The web store pakistan|
|Best buy monitors for gaming||Select the pick-up point and raise the array. Fastening bracket with angles for A10i. Page 8: How To Use This Manual Introduction How to use this manual The A10i a10i wide manual is intended for all actors involved in the system design, implementation, preventive and corrective maintenance of the A10i system. Restore password. Cancel Delete. Previous Next.|
|Slime laboratory||Read the technical description for an overview of all system elements, their features, and their compatibilities. Medium throw. It has been designed following the guidelines of BGV-C1. The screens are equipped with tabs to hold the grill in place when securing the screen on the enclosure. Lost your password?|
|Acer swift 3 i5||Introduced with K2 inPanflex offers the possibility to widen or narrow the directivity pattern of line sources a10i wide to adjustable L-Fins. Rear rigging plates for A15i and A10i onto or under KS21i. Always put the placeholder screws back in place to avoid leaks. Check out our Documentation Center for more documentations on this product. A10i-LIFT features two studs that match source lodgings at the front and rear of the enclosure. Use a shackle and a steel wire rope.|
|Saleka remain||Overview Full spec System Elements Downloads. User or email. Syva Sub. Page 3: Table Of Contents A10i system rigging Make sure the steel rope is as tensed as possible without bearing the load. One-channel speakON output custom speakON 2. Question about product.|
Always put the placeholder screws back in place to avoid leaks. A DINcompatible M8 threaded insert is available to implement a secondary safety. Multiple pickup points are available for site angle adjustments: 14 pickup points on each side, one front pickup point F , and one rear pickup point R. Page 29 Rigging system description When used at the top of the array as the main lifting accessory, A10i-RIGBAR can be secured at the front for an initial positive site angle.
A10i-LIFT features two studs that match the lodgings at the front and rear of the enclosure. Use a shackle and a steel wire rope. Make sure the steel rope is as tensed as possible without bearing the load. Page A15I-Bump Thirteen holes are available for site angle adjustment. For larger arrays, refer to Radial arrays of 7 enclosures and more p. One pickup point pickup point safety points Two pickup points safety point pickup points A10i owner's manual EN version 1.
Fasteners for wall-mounting or ceiling-mounting Select screw length and anchors applicable to the wall or ceiling properties. These two screws are secured in place of the grill screws. The screens are equipped with tabs to hold the grill in place when securing the screen on the enclosure.
It has been designed following the guidelines of BGV-C1. Page 50 Soundvision calculations are based on usual environmental conditions. A higher safety factor is recommended with factors such as extreme high or low temperatures, strong wind, prolonged exposition to salt water, etc. Always consult a rigging specialist to adopt safety practices adapted to such a situation. The [A10] preset delivers a reference frequency response in medium throw applications. Tools Before performing rigging procedures on this product, make sure all the tools listed are available.
Page 61 This step requires three operators. Hold the enclosure at the bottom until the rigging plates are secured. Check that all the screws are secured and tightened 5 N. What to do next Securing a screen p. Page 63 1. Prepare the KS21i enclosures by removing the placeholder screws and securing rigging plates on both sides. Page 64 Lift the rear of the new KS21i and secure it to the array by pre-tightening a rigging screw on both sides.
Page 65 Link the KS21i enclosures at the front with rigging screws. Apply a torque of 5 N. Page 66 Rigging procedures 5. Page 69 This step requires three operators. Select the pick-up point and raise the array. Raise the array until the bottom enclosure is accessible. Remove the screw from the bottom rear hole of the bottom enclosure on each side. Page 74 Rigging procedures 5.
Do not tighten the screws until all rigging plates are secured. Tighten all the screws on the rigging plates. Page 77 5. Page 78 Do not tighten the screws until all rigging plates are secured. Tighten all the screws on the rigging plates 5 N. Page 82 For a single enclosure: a. Rotate the enclosure to align the second insert with the selected site angle.
Drive a screw on both sides. Tighten all the screws. Apply a torque of 7 N. Page 83 Rotate the enclosure and the rigging plates to align the second insert and the rigging plates with the selected site angle. Page 84 Tighten all the screws. Page 85 Rigging procedures 7. A15i Focus A15i Wide Bottom A15i Focus A15i Wide If the two enclosures are misaligned at the front, loosen the screws on the U-rigging plates and realign the two enclosures, then re-tighten the screws.
Mount A-U15i on the ceiling or on the wall using four M10 screws. Page 87 6. Set the angle: a Rotate the enclosure and the rigging plates to align the second insert and the rigging plates with the selected site angle. Page 88 Apply a torque of 7 N. Page 92 Rigging procedures 4.
Prepare a new enclosure by removing the placeholder screws and securing rigging plates. Page 93 Hold the enclosure at the bottom until the rigging plates are secured. Link the two enclosures at the front by pre-tightening a rigging screw on both sides.
A10i Wide Performance and discretion 2-way passive, 10". Introduced for the first time in in the SB28, the laminar venting technology is a progressive vent design that drastically minimizes turbulence noise leading to an increase in output capability. All current L-Acoustics loudspeaker enclosures with low-range capacities feature L-Vents. Since , this major technological innovation is at the heart of every L-Acoustics line source element, with a specifically tailored WST for each product.
Introduced with K2 in , Panflex offers the possibility to widen or narrow the directivity pattern of line sources thanks to adjustable L-Fins. With Panflex, users can adapt the system coverage pattern to match the complex shape of any audience geometry. Related Products. Previous Next. Fixed Install. Amplified Controller. Need more information?
Max SPL, dB ; Bandwidth, 67 Hz- 20 KHz ; Transducers, LF: 1 x 10" HF: 1 x " ; Weight, 18 kg / 40 lb ; Directivity, H: 70° / 90° / ° V: 30°. A10 Wide. Performance and discretion. 2-way passive, 10" A10i Wide. Fixed Install. background image. LA4X. Amplified Controller. MILAN-Certified. The 30° enclosure of A10i Wide enables a compact array to provide expansive coverage while preserving sightlines. Panflex allows users to adapt directivity to.